The working principle of hydraulic shearing machine
When the upper cavity of the left cylinder of the machine enters the oil, the piston descends, and at the same time the oil from the lower cavity enters the upper cavity of the right cylinder to lower the piston, thereby ensuring the parallel movement of the blade carrier. When the amount of oil in the tandem oil circuit increases or decreases, the shear angle of the cutting blade changes accordingly. This kind of structure often uses a nitrogen accumulator to push-one or two return cylinders to shorten the inter-travel time, thereby increasing the productivity of the machine.
Shearing machine should be able to ensure the straightness and parallelism requirements of the shearing surface of the sheared sheet and minimize the distortion of the sheet to obtain high-quality workpieces. The upper blade of the shearing machine is fixed on the knife holder, and the lower blade is fixed on the workbench. Ball transfer table is installed on the workbench so that the sheet material will not be scratched when sliding on it. The back gauge is used for positioning the plate, and the position is adjusted by the motor. The sheet holding cylinders are used to compress the sheet to prevent the sheet from moving during shearing. The guard fence is a safety device to prevent work-related accidents. The cutting blade return stroke generally relies on nitrogen, which is fast and has little impact.
Before operating the shearing machine, wear tight-fitting protective clothing, fasten the cuffs, and do not open the hem of the jacket. Do not wear, take off or change your clothes next to the operating machine to prevent the machine from being twisted. Safety helmets must be worn, braids should be put inside the cap. Do not wear skirts, slippers, or scarves to operate the machine.
The operator must be familiar with the structure, performance, and operation methods of the equipment, and it is strictly forbidden to use the equipment over the performance standard.
Check the oil volume of the oil cup before starting and add grease according to the equipment lubrication regulations.
Before work, the upper and lower blades should be set to the knife. The blade gap should be determined according to the thickness of the sheared steel plate, generally between 5～7% of the thickness of the sheared plate. Every time the gap is adjusted, the flywheel should be turned by hand. Make the upper and lower blades reciprocate once and check whether the gap is proper with a feeler gauge.
Set and adjust the back gauge according to the requirements of the cut workpiece. Before working, you should try running for 2 to 3 times without load to confirm that the lubrication is good and there is no abnormality in the operation before you can start the work.
It is forbidden to use percussion method to adjust the back gauge device or adjust the blade gap. When adjusting the gap between the guide rail and the knife edge, stop the machine before proceeding.
It is forbidden to reach into the cutting area during the working process, and it is not allowed to pick up and pick up materials by hand.
No other items should be placed on the workbench to avoid entering the cutting edge and damaging the blade.
When cutting sheets of different thicknesses and different materials, the pressure of the plate spring and the blade gap should be adjusted appropriately to prevent the spring from breaking or damaging the cutting edge. It is forbidden to cut bars.
Always pay attention to whether the clamping mechanism, clutch and brake are abnormally malfunctioning; when cutting, you should concentrate on cutting. If you find any abnormalities in the equipment, you should stop cutting immediately, cut off the power supply, and notify the relevant personnel for maintenance.
The cutting edge of the blade must be kept sharp. If damage, wear, or dullness is found, it should be sharpened or replaced in time.
After the work is completed, the power supply should be cut off and the equipment should be maintained.
More experienced in design and manufacturing of shearing machines
Advanced machining equipment ensure the processing quality
Fast delivery
Fast response for service and warranty
What is a hydraulic shearing machine?Hydraulic shearing machine is a kind of sheet metal cutting machine. It can cut sheet metal to pieces as needed width. The power is from two strong hydraulic cylinders. Hydraulic oil is pumped by pump system to achieve high pressure. Hydraulic cylinders drive th
World hydraulic shearing machine operation instructionStep 1:Loosen the bolts on the top fuel tank, open the lid of the fuel tank, and fill it with 46# hydraulic oil. Fix the tank lid after full filling the hydraulic oil. Step 2:Connect the electric power input three-phase wires to the electric cabi
How to fill nitrogen and oil for QC11Y guillotine shearing machine accumulator QC11Y guillotine type hydraulic shearing machine has two hydraulic cylinders and an accumulator. The hydraulic cylinders drive the blade carrier down. The accumulator helps to drive the blade carrier back to top dead poin
0086 21 62828320
0086 13817120700
wang@worldpowerpress.com
